The NEW Reactor X2 has been redesigned to include our most requested feature, direct unregulated voltage to the cyclic servos while maintaining safe, regulated 5.2v power to the receiver, gyro, tail servo and other sensitive equipment.
As the unfailing heart of your helicopter. The Reactor X2 generates noticeable servo power, which provides consistency and agility for both 3D and F3C flight. Providing power to the servos and receiver on dual power bus voltage regulators, the Reactor X2 is one of the first of its kind to provide split power output and servo bus technology to the R/C heli market.
A lot is riding on the power system of any r/c heli, don’t trust anything less than Reactor X2… the old saying is true - you get what you pay for.
We’ve added what customers wanted to the popular, proven, and high quality ReactorX regulator.
The preset CCPM voltages are: 6.0V regulated for all standard and digital servos. 6.8V regulated for high voltage type servos and brushless series servos. In addition the new X2 now allows full unregulated Li-Po voltage (8.4V at full charge) to pass directly to the servos for maximum voltage to HV type servos.
Reactor X2 allows pilots to use HV servos on any type of receiver that normally would not allow direct Li-Po power supply. Certain Futaba, JR and other receivers do not permit direct Li-Po input voltage but can now be used with Reactor X2 by passing high voltage directly to the CCPM servos and a safe 5.2V to the receiver.
The original Reactor X was the first helicopter voltage regulator system to offer dual regulators with servo power bus connections. The challenge of any power system is to supply current to hard-working servos safely and with the lowest resistance possible. Single battery setups with undersize wires and connectors don’t cut it anymore. Reactor X and the NEW Reactor X2 solves the power supply issue.
CCPM Power Bus - Three heavy current users CCPM / Mech. Mix servos are connected to the dedicated power bus for direct, consistent regulated power straight from the battery pack. A flick of a switch sets this power bus to 6.0V or an ultra powerful 6.8V output or use the included jumper for unregulated 8.4V, Futaba BLS Brushless heli servo series will find the 6.8V setting just as fast as unregulated 7.4V setups, but more consistent feel flight to flight.
Receiver Power Bus - A dedicated noise-free linear regulator provides preset 5.2V power through three redundant leads to your receiver which provides over 5 Amps of current. This voltage is recommended to get the best out of every gyro and tail rotor servo. The steady power supply will eliminate any chance of receiver brown-outs. Signal output from the RX to the CCPM servo bus are carried through the included large gauge connection leads. The receiver is at safe voltage for any 4.8V rated equipment plugged in.
If you have a flybarless system, then you absolutely need a Reactor X2. No other regulator keeps sensitive flybarless systems safe like the Reactor X2.
Nothing could be simplier to hook up… just plug the the the Reactor X2 ports RX1, RX2 & RX3 ports into the flybarless sytems Aileron Servo Right, Aileron Servo Left and Elevator ports on the flybarless system, Everything else hooks up exactly the same,
By running a Reactor X2, only 5.2V of regulated power is transmitted to the flybarless system, protecting the electronics from dips and spikes as battery voltage changes in flight, So pick the Reactor X2, when you no longer have flybars.
Reactor X2 is not your average “shrink-wrapped” voltage regulator. Enclosed in a custom case, this power system is protected better from the elements and harsh environments of R/C helicopters.With details such as built-in fast charge lead, horizontal connector headers for more compact wiring and preset voltages make this the most user friendly plug-and-play system.
The electronics are professionally designed to be noise free, RF interference free, and contain the highest quality components available. All Reactor X2’s are factory tested and backed by the best warranty in the business. We guarantee it.
Reactor X2 has powered past and present 3D Masters, XFC, and F3C World Champions. This regulator system will be the last thing you need to worry about so you can focus on flying!
...It’s pushing 1000 flights! -Colin Bell
It takes a great pilot, but it also takes trustworthy equipment to take titles like these. Some of Reactor X2 top users include:
Colin Bell (CAN) XFC 3D
Scott Gray (CAN) XFC 3D & F3C
Dominik Hagele (GER) 3D Master ‘07
Hiroki Ito (JPN) F3C World Champion ‘05, ‘07, ‘09
Lukas Riva (SWI) 3D Master ‘08
Kyle Stacy (USA) Great Planes E-Fest ‘09
Bobby Watts (USA) XFC 3D
Chen Zarfati (ISR) 3D Masters ‘06, F3C
And many more…
I´m really impressed. The machine feels really agile and strong with 6.8V on the cyclic servos. It simply works like it has to! -Dominik Hagele
Servos, setup and radio equipment only go so far. The last piece of the puzzle lies in the power system. All the equipment needing power from the battery works better, faster and more consistent on Reactor X2.
Whether you prefer “direct li-po” power for the ultimate in speed, torque and peformace while still maintaining safe voltage for receivers, gyros and other equipment the Reactor X2 does it.
And for those that prefer the consistent flight to flight feel of regulated power the Reactor X2 does it too. With the user selectable, 6.0V or 6.8V, the Reactor X2 ensures consistent performance, whether the battery is 100% or 30% charged. The Reactor X2’s 6.8V power setting will match any direct voltage performance, without feeling any voltage dips encountered during high current extreme flight.
Setup with any switch harness, or use the included “pin” or jumper loop switch to turn off the Reactor X2. To turn on, simply pull the plug out of the extension lead and slide it over your TX antenna so it won’t get lost! The fast charge lead can be positioned for easy fast charge hookup, and voltage checking without pulling the canopy every time.
Whether you’re a hard core 3D pilot, seasoned F3C veteran, or a up and coming sport pilot, the Reactor X2 is the best regulator for all types of pilots, models and flying. And with the ever increasing popularity of flybarless systems, having a high quality, regulated power supply is even more critical.
For the ultimate in speed and consistent feel 90 and 50 class helis
The 8.4V Bus setting for the ultimate in speed, torque and performance for use with JR 8717HV servos. Lightweight TP2100 battery will offer 3-4 high energy flights, and low weight.
For non-HV servos such as the Futaba’s Brushless servos use the selectable 6.8V setting. This setup will offer consistent flight feel and keep your servos input voltage within the factory recommended ranges.
F3C / 90 SIZE SPORT FLYER
Precision JR 8317 servos are fast and offers a very smooth feel for F3C type flying. The large capacity Thunder Power 3300mah battery will allow many flights before charging is required (6-8 flights). This is the 2005, 2007 & 2009 2nd place power setup.
A smaller battery can be used for 50 size machines. Use this setting with any other analog or digital servos rated for 4.8V use.
Retail: $109.99 USD
Direct sales, dealer and distributor inquiries contact scott (at) scottgrayrc.com
PHONE 519 208-0361
FAX 519 749-1315
Reactor X2 is sold world wide at these any many other leading hobby stores and online shops.
Click here for a list of dealers.
620 Mountain Maple Ave.
P: +1 519.208.0361
F: +1 519.749.1315
2011 China International Airsports Fiesta: This was my second year attending this enormous air show. 100,000 (one hundred thousand) spectators attended! It is held at a dedicated use airport built especially for airsports and for this annual air show.
China AVIC UAV Cup - International UAV Innovation Grand Prix: This five day event was a large national event featuring UAV’s of all kinds with teams from many top universities and companies in China. The unmanned aircraft had tasks to complete, and land autonomously...